10 Tell-Tale Signs You Must See To Buy A Fiat Panda Key Fob Replacement

Reasons Your Fiat Ducato Key Fob 500 Key Fob Won't Work

A key fob from fiat car key 500 is a great way to open the doors and begin the car. There are many reasons the fob won't work. These include a dead battery or damage to the receiver module, water issues, and interfering.

This listing is for a NEW replacement fiat 500x key fob programming Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for your vehicle). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason your 500 key fob will not function is due to the battery is dead. Modern key fobs offer an operating range that is limited and must be within a few inches of the vehicle to function. If you are far from your vehicle and you press the key fob button, the car will not respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin-cell battery (Part Number CR2032) by a new one from a reputable brand such as Panasonic Duracell or Energizer. They can be found in your local hardware store or online.

After you've replaced the coin cell battery, you can test it by standing near your fiat panda key programming 500 and pressing the buttons. The parking lights should flash and the key fob should operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, it might be water damage that prevents it from interacting with the module inside your vehicle. Water damage can happen in many ways, including the simple splash or submerging the key fob in saltwater at the beach. If you believe your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work, your fob will probably require reprogramming by a professional locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can be particularly harmful to the circuit board of the fob and can cause it to short out and eventually end up dying. The fob getting wet is not an ideal idea, but if you drop it in a cup of water or forget to take it out of your pants pocket before running the washer Don't give up hope.

Take the battery off first. Clean the electronic chip using isopropyl ethanol or a similar product and then dry it thoroughly before replacing the battery. Next try the fob and check if it functions. If the key does not work, it may have to be changed. This is usually done by an auto locksmith or dealer.

If the key you have is older and has not been programmed for your vehicle then you'll need to replace it completely. This is a simple process that can be handled by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition of your car. They will also need to reprogram the fob to the car's system. This is a cost-effective and quick process that could be completed on the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote has a maximum range of 30 feet, so in the event that you are far from your vehicle it will not respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If your fob won't work after replacing the battery for the coin, also called a "button", "watch" or "button" it may be due to a malfunction on the internal circuit board. Reprogramming the fob typically resolves this problem. There are instructions on how to do this for all vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they lose tension it may prevent your battery from sitting properly and cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software problems or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances it is possible that the software will need to be reinstalled in your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be able to transmit or receive the signal due to interference. This is possible when the key fob is close to a radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not work could be due to a weak connection to the buttons or the internal chip, or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module, located beneath the dashboard, picks up radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery 12 volt for about 15 minutes by taking off the negative cable first then the positive cable. Then, reconnect the battery. This will clear any residual electrical charge, and then restart the car's computer. This will help you get your key fob working again. If the issue continues you should seek out a certified technician. They'll be able to identify the root cause of your problem.