The Biggest Issue With Fiat Panda Key Fob Replacement And How You Can Fix It

Reasons Your fiat 500 new key 500 Key Fob Won't Work

A fiat 500 key fob is a great way to unlock the doors and start the car. There are a variety of reasons why the fob could stop working. This could be due to a dead coin battery or damage to the receiver module, issues, and interfering.

This listing is for an NEW replacement fiat spare key Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local locksmith (click here to search for a Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob doesn't function is due to an inactive battery. Modern key fobs offer limited operating range and must be within a few inches of the vehicle to function. If you are not within your car and press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. They are available at your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while standing near your fiat punto remote key price 500. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the fob's key doesn't function after replacing the battery, it could be damaged by water that blocks it from connecting to the receiver module inside your vehicle. Water damage can happen in a variety of ways, such as simply splashing or submerging the key fob saltwater at the beach. If you believe your fob was exposed to water, put it in a rice bag to draw out the moisture. If that doesn't work the fob might require reprogramming by a professional locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to become shorted and eventually fail. Getting the fob wet is not a good idea however, if you drop it into the water in a cup or forget to take it out of your pocket before you run the washing machine do not give up hope.

First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl or a similar product. Then test the fob to verify if it is working. If the fob doesn't work then it might need to be reset. This is usually handled by an auto locksmith or dealer.

If your key is old and is not programmed for your vehicle it is necessary to replace it completely. A professional locksmith for cars can carry out this simple task. The locksmith needs to cut the key to match the ignition on your vehicle. The locksmith will also need to reprogram the fob into the vehicle's system. This is an affordable and quick procedure that can be completed on the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote usually has 30 feet of range or less and if it's far from your vehicle, it will not respond to your commands. You can easily solve this problem by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly called"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board problem. In most cases, reprogramming the fob will solve the problem. You can find instructions on how to Open fiat 500 boot without key to do this for all vehicles by searching YouTube or reading the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension, it can prevent the coin battery from sitting properly, and this will cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle because of software or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations they may have to reinstall the program in your body control module, too.

Interference

In addition to a dead coin battery, the key fob may not be able to transmit or receive the signal due to interference. This is possible when the key fob is close to the radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob might not function due to a bad connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or if you've tried everything at home to fix it (e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming, and using an alternative key fob. The receiver module, located under the dashboard, receives radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting every single system on board in your 500 keys, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will remove any remaining electricity, and restart the computer of your car. This will help you get your key fob to work again. If the issue continues, you should consult an expert technician. They will be able to identify the root cause of your problem.