The 9 Things Your Parents Taught You About Patio Door Lock Repair

Patio Door Lock Repairs

Over time, the wear and tear could cause lock malfunctions. There are a few basic steps you can take to ensure the security of your uPVC door.

If it's resetting the lock or cleaning the mechanism for locking these simple fixes will make your home more secure.

Clean the Lock

Although patio doors are an excellent way to let in the outside and keep out the elements, they can also be an issue for security when your lock isn't functioning as it should. Over time wear and tear, cold and hot weather dirt and debris could take their toll on your patio door's lock and make it difficult to open. Fortunately, with a little care, you can ensure your patio door locks repair door's locks always work properly.

It's important to first clean the patio door lock as well as all moving parts. This helps to remove any dirt and coatings that may be preventing the lock from functioning in the way it should. Start by wiping the moving parts on your repair patio door door lock with an aqueous cloth. Then, use a scouring cloth or rough damp cloth to scrub the dirt-infested parts of the door frame and frame. Then clean the lock with a dry towel to remove any remaining moisture. Let it air dry before you use it.

If you have an outdoor door that has a pin tumbler latch mechanism it is possible to apply lubrication to the lock by applying graphite powdered to the key or by using an lubricant based on Teflon like WD-40 Multi-Use. This type of lubricant is easy to apply, and doesn't break down as time passes. If you are unable to find an appropriate lubricant, you might use a pencil with an extremely sharp tip. Place the pencil into the lock, then shake it around to distribute the graphite.

sliding patio door repairs near me patio door tracks also require regular maintenance to keep them free of dust, dirt and other debris. These tracks are especially susceptible to snow, ice and other debris, which could cause them to jam or bind. This can make it difficult for your patio door to open and close.

Tracks for sliding patio Door lock repair doors and rollers can be cleaned by removing weather stripping that is damaged or dirty and then cleaning it, before reinstalling it. The same can be done for rollers on patio doors, which can be cleaned and sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, are operated by using 3 to 4 or sometimes, 5 point locking mechanisms. They include the lock cylinder and handle that is operated by a key. These doors also need maintenance, and specifically lubrication of the moving parts. This can be done with an oil that is thin however, never WD40. This should be done at least once a year.

If hinges that are sagging aren't the cause, the door may be skewed and catch or rubbing against the strike plate hole within the frame. Take off the strike plate and employ a sharp tool expand its mortise. This will permit the latch to fit properly into the hole, and prevent it from rubbing against the frame.

While the cylinder is out of the way take a measurement of its width using a book or piece of wood that can fit into the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder, and the inner dimension runs from the center of the adjustment screw to the end of the cylinder.

Check the lock's length

If your patio door latch is difficult to turn even after cleaning and oiling, it's possible that it's not aligned properly with the strike plate. Verify that the door is in a balanced position, and that the hinge screws are in good condition. In most cases, however, simply moving the strike plate upwards or downwards can fix the problem.

The latch might not work properly in the event that the strike of the lock is too small. In this situation you'll have to increase the opening using the hammer or chisel and then test the latch to make sure that it connects to the strike plate smoothly without rubbing against or landing on the door's frame jamb.

You should identify the type mortise lock you have before purchasing a replacement. This can be done by looking at the faceplate on the lock and determining whether it is round or square. Look at each screw hole on the current lock, and note their size. This will help you to locate an alternative lock that is the exact same width and fits into your existing hole.

In addition to identifying the current mortise lock you should also examine it for any bends or scratches that may need repairing. A damaged or bent latch is more likely than one that has been used a lot to break. Replace the lock if it shows evidence of damage.

After you've determined the type of lock replacement that you require Now it's time to begin the actual repair patio door lock. Take the old handle and spindle from the patio door, and then install the new one. Start by installing the interior handle. Align it with the spindle and then secure it into by using two screws or bolts. Install the exterior handle after the interior handle. After you've completed these steps check the handles to make sure that they can be shut and open easily and that the latch is in contact correctly with the strikeplate.

Check the Door's Strike

The door latch and strike plate are two components of the lock that work to ensure that the latch locks the door. Misaligned strike plate and door latches can cause the latch to not latch the door properly. This problem is usually very simple to solve.

First, examine the holes in the strike plate's receiving to make sure they are free of obstructions, such as dirt or plastic plugs. Then loosen the keeper screws that keep the strike plate in place, allowing it to move vertically but not detaching it from the frame of your door. Then, adjust the strike plate until its holes for receiving align with the latch hooks on the door latch. Once the strike plate is adjusted, tighten all screws and test to see if the door closes smoothly.

Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, however they're crucial for locking and unlocking your door. These metal plates are located at the top and bottom jambs of your door, where they support its latch. The door latch slides into this strike plate and creates the seal. If the strike plate is damaged, rusted, or is not installed correctly the latch may not properly lock the door.

The most common reason for an outdoor door lock to stick or not close is a misalignment between the latch and the strike plate. The easiest method to check for this is with the "lipstick test." Rub some lipstick on the edge of the deadbolt, then apply masking tape over it. When you close the door the lipstick will leave a mark on the tape, indicating exactly where the latch meets the strike plate. If the mark is too high or low you can alter the strike plate.

sliding glass patio door repair patio door locks help keep your home safe from intruders, and if they're not working correctly, you should solve the issue fast. By following these simple steps, you can fix your patio door's lock and regain its functionality within a short time.